Most people connect warmer weather with barbecuing, swimming, and bonfires, but Jeep fanatics only have one thought: “topless” driving. Driving down the road with the wind in your hair, music blasting, and the sun on your face is one of the best feelings in the world. It’s possible that you took the top down to go for a ride without even thinking about putting it back up when you first got your first Jeep.
A Complete Guide on Installing and Removing Soft Tops on Jeep Wranglers
Installation of a Soft Top Nowadays, a Jeep Wrangler is required. Jeep Wrangler, on the other hand, has proven to be one of the most practical automobiles. They are mainly used as a mode of transportation for families, and they are 4×4 vehicles. It’s worth noting that you’ll require a different Jeep Wrangler based on the weather or other circumstances.
How to perfectly put a soft top on a Jeep Wrangler
To begin, remove the hardtop and replace it with the soft top.
Step 1: Put the hood position frame together and secure it
The first step is to put the hood position frame in place and secure it. The top is attached to this metal structure. Without the use of any tools, the pilot’s frame locks into place on both the rear and front of the windscreen. On the inside of the Jeep, the pilot may be found running around the sides.
Step 2: Take a firm grip on the entire top, excluding the windows
Grab the entire top, including the windows on one side, and place it on the frame. Place the pilot on the latch on the front of the windscreen; the upper half has a plastic shoe on the front.
Step 3: Stretch the upper body with caution
Spread the upper section of the Jeep’s plastic back carefully and place runners in the corners.
Step 4: Get in the Jeep and secure the frame
Install the hood to the frame of the Wrangler. The clasps are positioned in the frame’s middle and back parts.
Step 5: Set up the stern windows
Install the soft retainers on the rails and zip the back traveler windows. This window is fitted with two closures and two fasteners. Set up the back window with the three zippers and the back section stabilizer bar that slips over the window in the same way. Place them on the metal rails, the two back parts of this bar.
Step 6: Determine the angle of the windows with respect to the door
Put the three metal clasps on the eyelets and hold the forward-facing windows. It’s affixed to the front door. Join the window’s corner to the door with a screw. The door, near the windscreen, has a clasp. To hold the window in place, place the retainer on the rail. If the Jeep has steel doors, you can skip the preceding step.
Step 7: Pull the hood over the clasps and secure it
The veil must be secured to the frame’s fasteners. All of these will be placed above the passenger windows at all times. It aids in the correct placement of the soft top.
How long does it take to install a soft top on a Jeep Wrangler?
Anyone can install a soft top in most circumstances with just a few simple tools and moderate mechanical ability. Installation can take anywhere from 1 hour to 3 or 4 hours, depending on which Jeep top you purchase.
How do you put the soft top back on a 2020 Jeep?
By pulling down on the handles, lower the sun visors and release the header latches above the windshield frame. To fold back into the Sun rider, push up on the soft top. Position Remove the plastic retainers from the tailgate retainers, then hold the lower tailgate bar on the rear window and rotate up and out to remove the retainers from the body. By moving left toward the Jeep’s driver side, you can remove the back window. Pull out the quarter windows from the body by gripping the plastic support at the back of the vehicle and tugging outward until it pops out of retainers. Pull down on the Sun rider latch on the driver’s side of the Soft Top.
How do you install a soft top on a 2021 Jeep Wrangler?
Raise the soft top from its back stockpiling area and overlap it over the casing top. Push the top forward until a tick is heard. Pull the connectors for the header locks and place them in the front window hooks. Pull the back sailboards down into their crease body retainer exactly over the back taillights. Fold the base of the window retainer into the crease in the casing retainer. Close the windows securely. After that, place the back window base rear end bar into its corresponding grooves inside the Jeep’s rear end. Rotate the back end bar in a clockwise direction. The sailboards should be folded into the body retainers. When the header is closed, it is completely shut down.
How to install Jeep soft top frame
Remove any soft top cloth that may still be there. Place your vehicle’s new top on it. Make bows out of the fabric. Place the fabric in the channel of the windshield. Put the front bow assembly together and secure it. Install the back corners in the sixth step. Ensure that the back rows are secured. The spreader rails should be secured in place. Inside the side curtain, through the retainer’s vertical door. Connect the body belt rail to the side curtains.