Jeeps

How to Remove Rear Drive Shaft of Jeep Wrangler

Will a Full-Size Mattress Fit in a Jeep Wrangler

You can remove the shaft from the yoke by slipping a small punch into two holes in the yoke and tapping it with a hammer.

How do you remove a rear drive shaft?

Before you begin, put on safety goggles and gloves.

1. Make a note of the drive shaft’s location. Before starting, make a note of the driveshaft’s orientation.

2. Remove the bolts that hold the drive shaft in place. Remove the mounting nuts on the shaft differential flange.

3. Remove the Flange from the Driveshaft.

4. Disconnect the drive shaft.

5. Examine the U-joints

6. Put the driveshaft back in place. Flange Bolts must be reinstalled.

How do you remove a rear drive shaft on jeep TJ?

To remove the driveshaft, simply loosen the yoke straps, release the two u-bolt straps on the lower section of the shafts towards the back, and pull the driveshaft away from the t-case. Without the rear driveshaft, the TJ can be safely driven… without a doubt. The transfer case, rear differential, front axle, and other components of the vehicle will be safe. If the front axle has a locker, it will be engaged when the TJ is in 4wd, making steering on the street difficult.

How do you remove a drive shaft?

The steps for removing a rear drive shaft differ depending on the vehicle, but they are always the same. Engine power is transferred from the transmission to the driver wheels through the drive shaft. There are several reasons to replace the drive shaft. Furthermore, in the case of exceptions, the U Joint bolt is more problematic than the rear drive shaft. So, how do you remove the drive shaft? It is not rocket science to complete this work; all that is required is that you properly follow the technique, as your vehicle will not be able to travel without its drive shaft.

1. Remove the Bolts and Mark the Drive Shaft

Before commencing the process of removing a drive shaft, you must first determine the exact size of the drive shaft. After placing the drive shaft in the proper position, this method will prevent driveline vibrations. Remove the shaft by removing the projection mounting bolts as well as you’ve marked the place. Lock tighteners may be used on some bolts to keep them from falling free during installation.

2. Remove the Flange from the Drive Shaft

By gently startling the drive shaft flange with a plastic hammer, it can be readily removed. In order to completely remove the shaft flange, ensure that the half back of the shaft is free, and that the centre support is removed. If you’re working on an ancient car, be cautious with the U joint cups because they have a high probability of slipping out. Use electric tape to hold the U joint cups in place in such situations, as it is one of the greatest maintenance recommendations.

3. Remove the Shaft from the Drive

You may now remove the drive shaft from the car because it is entirely loose. Slide the drive shaft out of the transmission case gently with both hands. Because there may be a few liquid leaks, it’s a good idea to keep a liquid basin or collector nearby. You can also repair the transmission tail or universal joints at this time. Look for any defects or damage in the U joint. Check the mobility and smoothness of the U joint in every direction.

4. Replace the Drive Shaft and any other parts that have been removed.

The final step is to reinstall the new drive shaft, but first oil the yoke to ensure good operation. Place the drive shaft in the designated location with care. The flange bolts must also be reinstalled. Finish up by double-checking that everything is in its proper place. This is how you gently and properly remove the drive shaft.

What does a jeep drive shaft do?

Your Jeep’s front and rear driveshafts are important components that connect to the transmission and differentials via universal joints. The driveshaft in your Jeep Wrangler is responsible for transferring torque from the transfer case to the differential and sending power from the engine to the wheels. The torque of your Jeep’s engine is measured in pounds per square inch. A driveshaft transfers that raw power to the differential, which allows your car to perform everything from skim down a freeway to surging out of a mud hole on the trail. Knowing when to replace your Wrangler’s driveshaft is crucial because the wrong shaft can easily break, causing your Jeep to break down.

Material fatigue accumulates during wheeling, generating cracks that subsequently cause the shaft to snap even under light driving loads, causing an inadequate driveshaft to fail some time after the stress has been applied. After installing any considerable suspension lift or power boost, a Wrangler driveshaft upgrade is almost always required. Let’s take a look at some of the signs that it’s time to upgrade to a better aftermarket driveshaft. The most common reason for replacing the stock part with an improved driveshaft is to install a Wrangler lift kit. When the suspension extends – when the axles and wheels move lower away from the body the driveshaft lengthens, and when the suspension compresses, the driveshaft shortens. When the wheels flex downward with 2 inches, 3 inches, 6 inches, or whatever extra travel the raise package permits, the stock driveshaft simply isn’t long enough to lengthen properly.

What is the price of a driveshaft replacement?

The cost of Drive Shaft Repair is usually determined by the origin of the problem and the speed with which it may be fixed. If you only need to replace it, expect to pay between $500 and $1,000. However, parts should cost around half that amount, and labor should cost roughly $200.