It’s a lovely day outside, and you can’t wait to get out in your Jeep Wrangler. The only difficulty is that you must first remove your hardtop. It doesn’t have to be difficult to remove the hardtop on a Jeep. You can remove your Wrangler top in no time with just a few tools and the assistance of a friend! If, like the Beatles, you despise asking for help, you may buy a hoist or mounting device to safely remove your Jeep roof on your own.
How to Remove Your Jeep Wrangler’s Hard Top in Steps
When you remove the hard top from your 2-door or 4-door Jeep Wrangler, you can quickly enjoy the fresh air, just like a Jeep should be driven down the road from West Virginia to Skyline Drive.
Step 1
Unscrew the rear fastener knob overhead on the speaker bar assembly, beginning on the driver’s side. Place it in a secure location, such as the console.
Step 2
Open all three L-shaped locks from above. Move the sun visor to the side after unclipping it. Remove the Freedom Panel from the roof by lifting the header latch above the windshield frame. Take it out of the Wrangler by pushing it up.
Step 3
Unscrew the Rear Fastener Knob on the passenger’s side and fully open the single L-shaped lock. Move the sun visor to the side after unclipping it. Lift up on the Header Latch immediately above the windshield frame to remove the Freedom Panel.
Step 4
Only apply to Wranglers with four doors: Remove the two screws that hold the hard tops of the driver’s and passenger’s doors together with your T-40 Torx Head driver.
Step 5
Remove the six Torx Head screws keeping the hard top in place in the Wrangler’s trunk compartment with your T-40 Torx Head driver. On both sides, there are three.
Step 6
Look inside the back left corner of the hardtop for the wire harness.Pull away from the top of the rear windshield washer hose to disconnect it.
Slid the red tab to the right and press on the sides of the clip to disconnect the electrical harness. To completely detach the harness, pull it out.
Step 7
Close the swing gate and get another set of hands ready to assist you in lifting and removing the hard top off the Jeep. Raise the hardtop on each side and walk it to the back of the Jeep.
Step 8
Return the hard top to the Wrangler with the assistance of a buddy. Check that everything is in place on all of the ledges, and that the six Torx Head screws are lined up and ready to be secured inside.
Step 9
Slide the red tab to the left to lock the clip and reconnect the electrical harness to the top. Reattach the top of the rear windshield washer hose.
Step 10
Replace the six Torx Head screws in the top of the Wrangler’s trunk compartment with your T-40 Torx Head driver.
Step 11
Only for Jeep Wranglers with four doors:
To completely secure your hard top, use your T-40 Torx Head driver to reinstall the Torx Head screws above the driver and passenger doors.
Step 12
Replace the passenger-side Freedom Panel on the roof, then the driver-side Freedom Panel on the roof, making that everything is in position.
Step 13
Attach the Rear Fastener Knob to the Speaker Bar Assembly on the passenger side. To secure the Freedom Panel, close the overhead L-shaped lock and press down on the header latch above the windshield frame.
Step 14
Attach the Rear Fastener Knob to the speaker bar assembly on the driver’s side. Close all three L-shaped locks, then secure the Freedom Panel by pressing down on the header latch and clipping the sun visor back in place.
How to take hard top off jeep wrangler unlimited?
You’ll need to remove or disconnect all of the securing points before you can pop the top on your Wrangler. To make it easier to reconnect your hardtop later, set aside a couple of containers or named packets to organize all of the jolts and bolts you’ll be removing.
How to take top off jeep wrangler 2020?
- The Freedom panels come out when you remove the JL Wrangler hardtop.
- Remove the remaining latches from the panels by going around them and unhooking them.
- You may remove the two panels from the JL Wrangler hardtop by unhooking all the latches and levers.
- A wiring harness and windshield washer fluid line on each side must be detached before you can begin removing the rest of the hardtop.
- Rep the same for the other side once the wire harness and bolts have been removed from the driver’s side.
- To lift the top, enlist the assistance of a friend. To remove it, start lifting from the bottom.
How to take top off jeep wrangler 2021?
Pull on the front of each roof panel’s safety latch to remove the panels. Push on each panel from the inside of the vehicle to remove them after the rotary latches.The electrical connector for the rear window defroster and wiper, as well as the washer fluid tube, must be disconnected before the rest of the roof can be removed. Six bolts must then be removed. The hardtop is secured to the Wrangler’s body with three bolts on each side. Using the tools available, get rid of them.
Can you take Jeep top off by yourself?
The only difficulty is that you must first remove your hardtop. It doesn’t have to be difficult to remove the hardtop on a Jeep. You can remove your Wrangler top in no time with just a few tools and the assistance of a friend.