Advertisement

What causes a clicking sound in rear wheel when driving

One of the most common issues when driving a car is a clicking sound that comes from the rear wheels. The rear wheels are supposed to be connected to the rest of your vehicle through either shafts or a driveshaft. This connection is crucial, because it allows the wheels to rotate at different speeds without causing damage. When the wheels are connected through dangerous mechanisms, however, they can easily cause damage to your vehicle. For example, if your rear wheel is always making a clicking sound while you drive, that is an indication that something isn’t right.

A bent wheel can produce a disturbing noise and lead to wheel misalignment

This is an indication that your car needs wheel alignment. If you hear clicking sounds when driving over bumps, it could be due to a bent wheel. A bent wheel can also cause vibrations in the steering wheel or other parts of the car. A bent wheel can happen when your car hits a curb while parking or while driving on rough roads.

This may cause the outer edge of the tire to contact the rim of the wheel, causing damage to both parts. The main causes of this problem include hitting curbs, hitting potholes and driving over speed bumps at high speed.

Bushings are bad and need to be replaced

If you have a clicking sound coming from your rear wheels when you are driving, it is likely that you have bushing wear. If your vehicle has been sitting for a long period of time and the bushings are worn out, they may not be able to stay in place while driving and will make a popping or clicking noise as they move around. This can also happen if the bushings were damaged by hitting something sharp, such as a curb or curbstone.

The solution to this problem is to replace all four bushings with new ones and then retorque them with an impact wrench. If you do not have access to an impact wrench, you should consider having a professional do this work for you because they will be able to use one while doing the job.

Axle nut is loose

If you hear a clicking sound when you drive your car, it could be a simple fix or something more serious. Here are some possible causes for the sound and how to fix them. If one of the nuts that holds the axle wears out or loosens, it can cause a clicking sound when you turn the wheel.

To fix this issue, tighten the nut with a ratchet and socket. If it is too tight, use an impact wrench instead of hand tools. This will ensure that you don’t over-tighten it and damage other components in your vehicle’s suspension system.

Spindle Nut Is Loose

The spindle nut is another fastener that needs to be tightened from time to time on most vehicles. It holds together different parts of the differential assembly and axle shafts. If this nut becomes loose, then it can cause a clicking sound when driving because there is movement in these parts when turning corners or accelerating quickly.

Damaged or loose wheel bearing will cause the noise, especially at low speeds

A clicking sound in your car’s rear wheel is usually caused by a damaged or loose wheel bearing, especially at low speeds. This condition can be dangerous if it’s not addressed quickly. The wheel bearings are located on the side of the wheel hub, inside the rear axle, and they keep the wheels turning smoothly. If they’re damaged or loose, they will wear out quickly and may cause your car to vibrate or make a loud clicking sound when driving.

If you hear this noise coming from your vehicle, it’s best to have it looked at by a mechanic soon. Your mechanic will inspect the vehicle for signs of damage and determine whether or not you need new wheel bearings installed.

If the CV joint is damaged, clicking noises will be heard when turning

Clicking noise in the rear wheel of your car is one of the most common problems. The main cause of this problem is a damaged CV joint. It is located between the transmission and the axle. This joint allows you to turn the wheels without any resistance from the drive shaft.

If you have noticed that there is a clicking sound when turning, it means that your vehicle has a problem with its rear wheel drive system. The CV joint can be damaged due to several reasons:

  • Excessive use or misuse of your vehicle, especially off-road driving;
  • Incorrectly installed parts;
  • Inadequate maintenance;- poor quality parts.

A broken axle may also cause a clicking noise while driving

The clicking sound can be caused by a broken axle or ball joint, or the bearings could be worn out. This is a serious issue and requires immediate attention. The axle needs to be replaced as soon as possible to avoid further damage to your vehicle.

  • A worn-out bearing can also cause a clicking sound in the rear of your car while driving.
  • If the wheel bearings are worn out, they may need to be replaced along with the hub and wheel assembly. The wheel bearings are located on either side of the wheel between the outer rim of the wheel and the inner rim of the wheel.

The outer part of each wheel bearing has ball bearings that allow it to spin freely when you turn your steering wheel. When these ball bearings wear out, it can cause a clunking or clicking sound when turning left or right. A broken axle may also cause a clicking noise while driving.

Conclusion

It’s difficult to pinpoint the exact problem without seeing your vehicle, but there are some common causes of noises that can help identify and eliminate the issue. A clicking sound may be emanating from one of your brakes, so you should have them checked first by a mechanic. If you’ve ruled out your brakes as the issue, there’s a chance your axle bearings could be in need of replacement. To learn more about these common problems, check out our guide on driving noises , which has plenty of additional information on not just clicking sounds but all manner of noises.