How to Aim Jeep Wrangler Headlights

Jeep headlights have two adjustment screws, one on top for vertical adjustment and one on the side for horizontal adjustment.Turn on your headlights and get your Jeep as close as possible to the flat surface/garage entrance. Put some painters tape in the shape of a cross (or a plus sign or a lowercase T) on the wall directly across from your headlights, just in the center of where the light beam is brightest (here is where some of you “frugal” LED headlight owners may have some difficulty, but try your best). They should be separated by the same amount as your grill’s headlights. Retrace your steps back 25 feet. Keep an eye out for anything coming up behind you, such as children, bicycles, exotic dancers, and so on.

I park about 20 feet away from a wall and switch on my lights, putting chalk marks as close as possible to the center, top, bottom, and sides of the old beam, and then adjusting the new lights to match it as closely as possible, making sure the car is parked in the same spot. I’ll place them a hair lower than where they were originally positioned when the vehicle is elevated and I’m adjusting as a result of that. If this isn’t possible, line up two comparable cars and try to match the beam patterns.

Required materials and tools:

• Chalk
• Masking tape
• Driver Torx T-15
• Measuring tape
• Preparation

Mark a level horizontal line exactly three feet up a perfectly vertical surface using masking tape (or electrical tape, as in my case). Next, create a line for the front of the Jeep 25 feet out, perpendicular to your vertical wall.

Make the necessary changes

To see where the headlights are now aimed, turn on the low beams on the vehicle. Even at sunset, I thought waiting another 30 minutes or so would have been simpler.)

What’s the Best Way to Aim a Jeep Wrangler’s Headlights?

This alignment can be accomplished in a few ways. Because, unlike other vehicles, jeep ride height is easily changed with the load thanks to the soft springs, I’ll show you the two easiest and quickest ways to do this.After aligning your headlights, you may need to align them again if you upgrade your front bumper to a heavy bumper and add a winch.As a result, it’s preferable to choose for a simple and rapid method of headlight adjustment.

How to properly adjust headlights

When driving down the road or path at night, the proper adjustment and aiming of your LED illumination can make all the difference. Oncoming traffic can be blinded by lights that are not correctly focused, resulting in a collision or worse. Furthermore, badly placed auxiliary LED lighting might cause light to be wasted or underutilized since it is thrown off into oblivion.

You must first determine whether you have LED projectors or LED reflectors before properly aiming your LED headlights. To magnify the light and generate a nice, sharp cutoff, LED projectors employ a projector-style lens. LED reflectors resemble factory headlights in appearance, but instead of a halogen bulb, they use much brighter and longer-lasting LED chips with correct LED optics.

The jeep should be parked correctly

To begin, parallel park the jeep against the wall.Then, on the ground, measure 20 feet from the wall and make a 20-foot mark.Then drive to the 20-foot mark with the jeep facing you. Headlamps on Jeeps should be pointed at the wall.Both headlamps should be parallel to the wall at this point, with a spacing of 20 feet between them and the wall.Ensure that your floor is completely level. Without inclines or drops, the wall and the jeep should be on the same plane.

The jeep’s four wheels should all be level

‘I’m going to make a 3-foot mark on the wall.’Now, measure 3 feet from the ground from the driver’s side of the jeep and use the sticky tape to make a mark on the wall.Then measure 3 feet from the jeep’s passenger side and make a second mark on the wall.

Attach two markers on the wall with a long tape.

Now, on the wall above the ground, this will act as a 3-foot height indicator.

The headlamp beam can be adjusted.

After completing the preceding steps, you should now have a marker line on the wall 3 feet above ground level and a jeep parked 20 feet away, parallel to the marker line. Turn on your headlamps and set them to a low beam setting

How do I aim my headlights on my Jeep Wrangler?

Jeep headlights have two adjustment screws, one on top for vertical adjustment and one on the side for horizontal adjustment. Turn your headlights on and get your Jeep as near to the flat surface/garage door as possible.

How to aim headlights on 88 jeep wranglers?

Your Jeep Grand Cherokee’s hood should be open. To reveal the alignment screws on the headlamp, lift the headlamp covers. The alignment screws should be rotated using a Phillips screwdriver, Torx tool head, or Allen wrench. The headlight beam should be three feet above the ground.

How do you adjust the headlights on a 2019 Jeep Wrangler?

When adjusting your headlamps, make sure they’re on LOW, not HIGH. Turn the adjusters clockwise (to the right) to go UP, and counterclockwise (to the left) to go DOWN, while looking down at them.

How high should headlights be aimed?

For most cars, the top of the low beam that shines on the wall should be at or slightly below the height of the headlight lens’s center. The light pattern should be higher on the right side (passenger side) to illuminate road signs and lower on the driver’s side to prevent other drivers from being blinded.