How to Do an Oil Change on a Jeep Wrangler

Your vehicle’s lubrication is inadequate if the oil is dirty. Keep your Jeep running smoothly by changing the oil on a regular basis. The instructions below will demonstrate how to replace your oil properly.

Step 1: Locate the two grey latches on each side of the hood near the headlights to release the Jeep Wrangler hood.

Step 2: To release the latches, pull the latches away from the hood. Pull up on the lever in the front centre of the hood from beneath it. The hood is now open. Place the hood support rod in the designated hole on the hood’s underside to prop it open.

Step 3: Replace the oil in your Jeep Wrangler

On the top of the engine, look for the oil cap indicated in red in the image. To avoid losing the cap, keep it in a safe place.

Step 4: Underneath the vehicle, put the oil drain pan. Find the drain plug for the oil. It can be found towards the vehicle’s bottom indicated by the red square in the image. In order to catch all of the old oil, the pan must be placed directly underneath the oil drain stop.

Step 5: Remove the oil drain plug with a socket wrench and an adequately sized socket. An adjustable wrench will suffice in a pinch. To loosen it, turn it counterclockwise. Drain the oil from the car into the drain pan entirely. Twist the plug counterclockwise to replace reinsert it. Using the wrench, tighten it in a clockwise direction. Wipe down the plug with a dirty rag after it’s been reinstalled to remove any external oil. Oil will not drip onto the ground as a result of this.

Step 6:  Move the drain pan to the vehicle’s front. Make sure there are no oil spills! Attach it to the oil filter right beneath it indicated by the red square in the image. From the front of the engine, underneath the hood, this image is taken.

Step 7: As soon as you remove the filter, oil will begin to flow. Make sure the drain pan is full with oil. Turn the oil filter counterclockwise to loosen it up. The oil filter may be more easily accessed from the engine’s top side. Use an oil filter wrench to loosen it if twisting it by hand is too tough.  In the oil pan, place the removed oil filter.

Step 8:  Look for any loose rubber gasket portions in the socket. Clean the area by removing these and wiping it down. Remove the old oil filter from the socket and replace it. To secure it, twist it in a clockwise direction. Tighten it up using the oil filter wrench.

Step 9:  Look for the hole for the oil cap you took off earlier on the top of the engine. Pour 5.5 gallons of 5W-20 Motor Oil into the hole with the use of a funnel. Make sure each oil container has completely drained.

Step 10: Re-twist the oil cap clockwise. Make sure it’s screwed down securely.  Turn on your car and let it idle for roughly a minute. Allowing your engine to run will allow oil to flow through it.

Step 11: Make sure you have enough oil. Find the oil dipstick first marked in the first image by red. Using a paper towel or rag, wipe the oil dip-stick clean. Completely re-insert the oil dip-stick and carefully remove it. Ensure that the oil reaches the stick’s safe-fill region marked in the image in yellow. If it doesn’t reach this point, pour in more new oil through the funnel until it does. Never pour your oil down the sink. This is a huge environmental disaster. Consider your actions. Make sure your old oil filter and dirty, old oil are properly disposed away.

How do you change the oil in a Jeep Wrangler JK?

Step 1:  Draining the engine oil is the first step. It’s better to drain engine oil after it’s been running for a while and the oil is warm.

Step 2: Replace the oil filter Engine: 3.6L Pentastar

Step 3: Add oil to the engine.

Step 4:  Start the engine and look for leaks.

Step 5: Reset the oil service indication.

How often should Jeep Wrangler oil be changed?

The Owner’s Manual for the Jeep Wrangler recommends changing the oil and filter when the Oil Change Indicator System indicates it’s time, but not more than 12 months or 10,000 miles apart, whichever comes first.

How long can a Jeep Wrangler go without an oil change?

Oil changes are usually required after 5,000 to 7,500 kilometres. Furthermore, if you use synthetic oil in your vehicle, you can go 10,000 or even 15,000 miles without changing the oil.

What type of oil change does a jeep wrangler need?

Every 7,500 to 10,000 miles, synthetic oil should be changed. For traditional oil, Jeep suggests changing the oil and filters on your 2020 Jeep Wrangler every 3,000-5,000 miles. An oil change is one of your vehicle’s most important services. Synthetic oil is preferable to regular oil for your engine. Although conventional oil (mineral oil) can offer enough lubrication, synthetics give superior overall engine efficiency and protection. Six quarts of 5W-20 oil are recommended by Mopar. You can also use 5W-30 depending on the temperature (extreme hot/cold). Mopar® API SP/GF-6 Certified SAE 5W-30 Full Synthetic Engine Oil, which complies with FCA Material Standard MS-13340, is recommended in the handbook.

Why can’t you use conventional oil again after using synthetic?

Leaks occur as a result of the switch to synthetic oil: Leaks are uncommon when converting to synthetic oil. Synthetic oil is thinner than regular oil, allowing it to flow more freely. You won’t be able to go back to regular oil: You are not obligated to use synthetic after making the transition.